Does The Everbilt 4 In. Dryer Lint Clean Out Connector Work With Ridgid Ducting

The skillful news: The four-inch white plastic or aluminum-foil exhaust ducting commonly used to connect a clothes dryer to an exterior vent is easy to install. Its spiraled-wire interior is extremely stiff and flexible and, at 50 cents to $i per human foot, this hose-like product is inexpensive. But the ducting isn't the all-time choice: It doesn't do a good job of exhausting hot air and, in some cases, it can be dangerous.

The ribbed, corrugated surface inside the pipes acts like hundreds of tiny speed bumps, disrupting and slowing the airflow. Equally a result, information technology takes longer to dry clothes, wasting energy and money. In addition, the interior traps lint, which too reduces airflow and, in extreme cases, overloads the motor and shortens the life of the dryer.

More important, an accumulation of lint is a fire hazard. In a gas dryer, a lint fire can melt the plastic ducting and commencement a house fire. For this reason, building codes prohibit using it, and possessor's manuals warn confronting information technology.

What Is the All-time Dryer Vent Hose to Employ?

The solution is to install a rigid-metal vent pipage. Its smooth interior creates very little air resistance, which makes the dryer more efficient, and discourages lint buildup. We replaced an 8-foot-long plastic flex hose with a smooth-metal vent and shaved 10 minutes off the drying fourth dimension of a full load of wearing apparel. Here's how nosotros did information technology.

Dryer Vent Installation in 6 Steps

Step 1: Pull the dryer away from the wall

• Outset, carefully pull the dryer away from the wall and disconnect the power cord. (If it's gas-fired, be sure to shut the gas valve too.)
• Adjacent, apply a screwdriver or nut driver to loosen the band clench that secures the plastic vent to the exhaust outlet.
• Pull the vent off the outlet and vacuum away any lint you detect inside the dryer.
• Then, disconnect the other end of the plastic vent from the ducting that goes exterior.
• Again, use a vacuum cleaner to clear lint out of the circular duct.

Footstep ii: Tighten the clamp

• Skid a metal band clamp over the lower cease of the periscope box vent and printing information technology onto the exhaust outlet.
• Holding the vent steady, tighten the clench with a screwdriver until it feels snug.

Stride 3: Attach the periscope

• Grab hold of the upper section of the periscope and lift up until it'southward a couple of inches in a higher place the back of the dryer.
• Plugin the ability cord (plow the gas dorsum on if necessary) and carefully push button the dryer back against the wall.

Pace iv: Employ dryer vent kit to bring together the box vent to duct

• All that's left to exercise now is to join the box vent to the overhead duct with the vent kit.
• Start by attaching the lower flex vent to the periscope box vent.
• Secure the elbow with a ring clench.

Stride 5: Attach a 90-degree elbow

• Then skid a band clench onto the overhead duct, insert the male finish of the 90-degree elbow into the duct and tighten the clench.

Step half-dozen: Terminate by connecting

• Side by side, pull up on the lower flex vent and tug down on the upper vent until the two ends meet midway between the dryer and ceiling.
• The ends of the vents accept especially designed quick-lock fittings that snap together—no band clamp is needed.

Later on yous've made all of the necessary connections, it's time to test out the revamped vent organization. Plough on your dryer and verify that air is blowing through the vent hood that'south mounted on the outside of your business firm.

---

Tools

Source: https://www.thisoldhouse.com/laundry/21016660/how-to-upgrade-a-dryer-vent

Posted by: woffordmined1938.blogspot.com

Share this post